{"product_id":"interior-wood-care-flat-matt-oil-based-resene-qristal-clear-polyurethane-4l-colour-clear-colourless","title":"Interior Wood Care Flat (Matt) oil-based Resene Qristal Clear Polyurethane 4L - Colour: Clear Colourless","description":"\u003ch2\u003e\u003cstrong\u003eWood Care Paints\u003c\/strong\u003e\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eProduct category: \u003c\/strong\u003e Floor Sealer\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eColour: \u003c\/strong\u003eClear matt finish - no tint\u003c\/p\u003e\n\u003cp\u003e\u003cmeta charset=\"utf-8\"\u003e\u003cstrong\u003eBrand name \u0026amp; product:\u003c\/strong\u003e \u003cmeta charset=\"utf-8\"\u003eCabot's Clear CFP Floor\u003c\/p\u003e\n\u003cul data-locator=\"features_list\" class=\"featuresWrapper\"\u003e\n\u003cli class=\"features\"\u003eHighly durable\u003c\/li\u003e\n\u003cli class=\"features\"\u003eHard wearing\u003c\/li\u003e\n\u003cli class=\"features\"\u003eFast drying finish\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cdiv\u003eCabot's CFP Floor Water Based is a hardwearing, clear floor coating suitable for all interior timber parquetry and cork flooring. Highly durable, it’s been formulated to be hard wearing and has a fast drying finish. No sanding is required on pre-coated timber, saving you time and hassle.\u003cbr\u003e\u003cbr\u003ePreparation\u003cbr\u003e\u003cbr\u003e^ No sanding required for pre-coated timber floors, preparation steps below must be followed. Please note new timber must be sanded.\u003cbr\u003e\u003cbr\u003eRemove stains, dirt, wax, grease and oil with mineral turpentine.\u003cbr\u003e\u003cbr\u003eRemove any polish with a suitable floor polish remover.\u003cbr\u003e\u003cbr\u003eNote: Floors with highly visible scratches, imperfections or floors that are severely worn must be sanded prior to coating.\u003cbr\u003e\u003cbr\u003eBare Timber\u003cbr\u003e\u003cbr\u003eSand the surface smooth using 180 - 240 grit sandpaper. Sand only in the direction of the grain. Remove all traces of sanding dust.\u003cbr\u003e\u003cbr\u003ePreviously coated floors and timber floating floors\u003cbr\u003e\u003cbr\u003eThoroughly clean the surface with Cabot's Floor Clean and allow to dry. Apply one coat to a small test area. Allow to dry for 3 hours. Press sticky tape firmly to the surface and pull off quickly. If the coating comes off, sanding back to a sound surface will be required.\u003cbr\u003e\u003cbr\u003eNote: Fill nail holes, cracks and other defects with Cabot's Wood Tone Putty after applying the first coat of this product for accurate colour matching.\u003cbr\u003e\u003cbr\u003eApplication\u003cbr\u003e\u003cbr\u003eApply with 6-10mm nap roller, brush, pad applicator\u003cbr\u003e\u003cbr\u003eNote: Do not shake can.\u003cbr\u003e\u003cbr\u003e1. Stir thoroughly with a broad flat paddle before and during use.\u003cbr\u003e\u003cbr\u003e2. Use a brush to cut in around the edge of one section at a time.\u003cbr\u003e\u003cbr\u003e3. Apply product with a pad applicator, good quality brush or 6 - 10mm nap roller. Coat along the length of 3 - 4 boards, keeping a wet edge to prevent lap marks.\u003cbr\u003e\u003cbr\u003e4. Allow to dry for a minimum of 3 hours. For best results, lightly sand to remove any grain raise using 240 grit paper. Remove all sanding dust.\u003cbr\u003e\u003cbr\u003e5. Apply the 2nd and 3rd coats as above.\u003cbr\u003e\u003cbr\u003eBare timber floors\u003cbr\u003e\u003cbr\u003eApply 3 coats, allowing 3 hours between coats.\u003cbr\u003e\u003cbr\u003ePreviously coated floors -\u003cbr\u003e\u003cbr\u003eApply 2 coats, allowing 3 hours between coats.\u003cbr\u003e\u003cbr\u003eStaining bare timber floors\u003cbr\u003e\u003cbr\u003e1. If staining is required, apply 1 coat of CFP Floor Water Based as a sealer.\u003cbr\u003e\u003cbr\u003e2. Apply 1 - 2 coats of Cabot's stain and varnish water-based with a 6 - 10mm nap micro-fibre roller.\u003cbr\u003e\u003cbr\u003e3. Finish with 2 coats of Cabot’s CFP floor water based following application instructions above.\u003cbr\u003e\u003cbr\u003eNote: To stain a previously coated timber floor, sand back to bare timber before staining.\u003cbr\u003e\u003cbr\u003eMaintenance\u003cbr\u003e\u003cbr\u003eCabot's Floor Clean is recommended for regular cleaning.\u003cbr\u003e\u003cbr\u003eOnce your timber floors have become excessively scratched, it's time for a re-coat with Cabot's CFP Floor Water-based.\u003c\/div\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"Circle Paints","offers":[{"title":"Default Title","offer_id":52509127999719,"sku":null,"price":29.0,"currency_code":"AUD","in_stock":false}],"url":"https:\/\/circlepaints.org.au\/products\/interior-wood-care-flat-matt-oil-based-resene-qristal-clear-polyurethane-4l-colour-clear-colourless","provider":"Circle Paints","version":"1.0","type":"link"}